Plumbing Basics: Before Installing a Bathtub
Plumbing Basics: Before Installing a Bathtub
Blog Article
This article listed below on the subject of How to Install a Bathtub Yourself is immensely intriguing. Read on and make your own personal ideas.
Mounting a bathtub isn't specifically rocket science, however it does require solid plumbing, woodworking, and in some cases, tiling skills. Replacing an old tub with a brand-new one is additionally a moderately challenging job. If the old tub is readily easily accessible, the task can move easily; if you need to open a wall surface to get rid of the old bathtub as well as position the brand-new bath tub, the job is much harder. In either case, the job is within a residence handyman's abilities, although you will certainly need a helper to vacate the old tub as well as set in the new one. See to it you have qualified on your own for the task and fit trying it. Rather than employing a specialist to take over a halfway-completed project, it is far better to think about employing one before you begin. Chances are you may require a specialist plumber to make tube links.
This post will certainly assist you install a brand-new bathtub in your shower room if you have actually currently acquired a brand-new bathtub and also don't need to change the plan of your previous supply of water pipelines.
Your tools and also material list need to make up the following:
Preparing for the Setup
Firstly, the supporting framework provided with the bath needs to be fitted (if needed) according to the supplier's guidelines. Next off, fit the taps or mixer to the bath tub. When suitable the faucet block, it is essential to see to it that if the faucet features a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps unit to stop strain on the tub.
Fit the flexible faucet ports to the bottom of both taps using 2 nuts and olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath must currently be ready to be fitted in its final setting.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installation, after that the first thing you need to do is disconnect the water. After doing so, switch on the faucets to drain any water continuing to be in the system. The process of eliminating the existing faucets can be fairly problematic because of the restricted accessibility that is commonly the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the faucets. Have a towel prepared for the continuing to be water that will certainly originate from the pipes. As soon as the supply pipes have been gotten rid of, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from transforming throughout this procedure. Once the taps have been removed, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Prior to moving on to fit the brand-new taps, contrast the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Bath tub
Using both wooden boards under its feet, place the bathtub in the required placement. The wood boards are handy in equally spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto four small factors.
The next objective is to make certain that the tub is leveled all round. This can be accomplished by examining the level and changing the feet on the bath tub until the spirit level reviews degree.
To set up taps, fit the bottom of the outermost flexible faucet port to the suitable supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Activate the supply of water as well as examine all joints and also new pipework for leaks as well as tighten them if necessary. Load the bathtub as well as additionally inspect the overflow outlet and also the typical outlet for leaks.
Lastly, repair the bath paneling as defined in the supplier's instruction manual. Tiling and also securing around the bathtub should wait up until the tub has been made use of at the very least once as this will certainly settle it into its final position.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic adapter to prevent damages to the string. One end of the port fits on the plastic tail of the tap as well as the various other end gives a link to the existing supply pipes.
If you need to fit a monobloc, after that you will need reducing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making certain that the washers are in place in between the faucet and also the sink. Secure the tap in place with the producer offered backnut. When the tap is safely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with regular faucet adapters. The previous type needs to be linked to the tap finishes first, tightening up only by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath meets the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the fitting can relocate sufficient to split a rigid seal, triggering the water to pass through the wall between the bath as well as the tiling, resulting in issues with wetness and also feasible leaks to the ceiling below.
You can choose from a variety of coloured sealers to blend in your fixtures and also installations. They are marketed in tubes and also cartridges, and also can securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of drenched newspaper or soft rope. Remember to constantly load the bath tub with water before sealing, to allow for the movement experienced when the bathtub remains in usage. The sealant can crack rather early if you do not think about this activity prior to sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also quickly readily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing waterproof or water-proof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a fervent reader about Installing A Bathtub, I was thinking sharing that segment was a good thing. Are you aware of somebody else who is excited about the topic? Why not promote it. Thank you for your time invested reading it.
Search-end for emergency plumbing. Report this page